Serving the Greater Toronto Area

Mon–Sat, 8 a.m. – 9 p.m.

capservicepro@gmail.com

Hot Tub & Spa Repair in Toronto & GTA

Diagnostics and repair for hot tubs and spas, from heaters and circulation pumps to control packs, topside panels and electrical faults.

Hot Tub & Spa Repair: what we fix

The problems we are called for most often. Not on the list? Describe it in your request.

  1. Water will not heat

    Failed heater elements, pressure or flow switches and sensors that stop the heater from running.

  2. Error code on the panel

    Flow, overheat and sensor codes traced to the actual fault instead of reset and forgotten.

  3. Jets or pump not working

    Pumps that hum, leak or stop, seized motors and jets with no pressure.

  4. GFCI trips at start-up

    Moisture in components, a failing heater or pump, and wiring faults found step by step.

  5. Topside panel is dead

    Blank or unresponsive controls, failed control boards and damaged cables.

  6. Leaks under the cabinet

    Pump seals, unions, heater fittings and jet bodies that let water out.

Brands we service

  • Hydropool
  • Jacuzzi
  • Sundance
  • Hot Spring
  • Caldera
  • Arctic Spas
  • Beachcomber
  • Coast Spas
  • Bullfrog
  • Master Spas
  • Marquis
  • Dimension One
  • Artesian
  • Vita Spa
  • Sunrise Spas
  • DreamMaker
  • Wellis
  • Viking Spas
  • Balboa

Brand names and logos are trademarks of their respective owners. CAP Service Pro is an independent service company and is not affiliated with these manufacturers.

Hot Tub & Spa Repair in the GTA

A hot tub is a small pool packed into a cabinet: a heater, one or more pumps, a control pack, a topside panel and sensors that protect all of them. Because the control pack shuts the heater off whenever something looks wrong, many problems first appear as an error code on the panel. Flow errors usually mean a dirty filter, low water or a failing circulation pump. Overheat codes can be a sensor, a stuck relay or a pump running too long. A tub that trips the GFCI breaker usually has moisture in a component or a failing heater element or pump motor, and it needs careful testing rather than repeated resets.

Before you call

  • Clean or swap the filter and check the water level; these two fix many flow codes.
  • If the tub trips the breaker, leave it off and do not keep resetting it.
  • Write down the code on the topside panel and the make of the tub and its control system.

Repair or replace?

Heaters, pumps, control packs, topside panels and sensors are standard repairs on most brands, including tubs with Balboa and Gecko control systems. A cabinet or shell that leaks from many places on an old tub is usually where replacement starts to make sense, and we will say so.

The diagnostic visit is a flat $99, and you get the repair price before any work begins. Completed repairs are covered by our warranty. We service hot tubs and spas at homes, hotels, gyms and rental properties across Toronto and the GTA.

How a service call works

  1. Step 1: Request

    Book a time online, or call, email or send the form and we set a time with you.

    Online, phone or email
  2. Step 2: Diagnose

    A technician inspects the equipment and finds the actual cause.

    Flat $99 diagnostic
  3. Step 3: Quote

    You approve the price before any repair work begins.

    Price before any work
  4. Step 4: Repair

    The repair is completed and tested before we leave.

    Covered by warranty

Common questions

Anything else? Call us and ask.

My hot tub shows an error code. Should I keep resetting it?

No. Repeated codes usually point to a real fault. Turn the tub off at the breaker if it keeps tripping and send us the code.

Can I leave my hot tub empty over winter?

Only if it is winterized properly: drained, the lines blown out and the pumps and heater protected. Water left in the plumbing can freeze and crack them, which is why many owners in Ontario keep the tub running all winter.

Where do I find the make of my tub and its control system?

The tub brand is usually on the cabinet or the topside panel. The control system brand, often Balboa or Gecko, is printed on the topside panel or on the control box behind the equipment access door. A photo of either helps us prepare.

Across the Greater Toronto Area

Toronto and communities within about 50 km of downtown. Pick a place on the map to check it.Not sure if we cover your address? Send your postal code with the request.

Service available

Toronto

The centre of our service area: everything within 50 km of downtown.

Brands we service

  • Whirlpool
  • LG
  • Samsung
  • GE
  • Frigidaire
  • Bosch
  • KitchenAid
  • Maytag
  • Lennox
  • Carrier
  • Goodman
  • Rheem
  • Hayward
  • Pentair
  • Jandy
  • Balboa

All major residential and light-commercial manufacturers. Brand names are trademarks of their respective owners; CAP Service Pro is an independent service company. Map data © OpenStreetMap contributors.

Service request

What needs repair?
Property type

For example, M5V 2T6

    Include the brand and model, or attach a photo of the rating label or the error code.

    We use your details to respond to this request and provide the service. Privacy policy

    CallBook a service visit